Hardware Manuals

Rane - Sixty Two  

Advanced Audio Setups

As mentioned, the Rane 62 is offering a pre-defined audio configuration for Timecode (DVS) and Sampler routing to the AUX USB Channel. Further details and alternative setups are described below.

Timecode (DVS)

VirtualDJ is offering DVS (Digital Vinyl System) support for the Rane 62. A Timecode Plus or Pro Infinity license is required. 2 Timecode Inputs are available to control any software decks via Timecode CDs or Vinyls.

Both Mixer Decks can accept LINE ( Timecode CDs) and PHONO Sources ( Timecode Vinyls) depending on the LN/PH switchers at the rear panel of the unit.
Inputs 1 or 2 can be used as Timecode for the left Deck and Inputs 3 or 4 for the Right Deck.
By default VirtualDJ has pre-configured Timecode to Inputs 1 for the left and Inputs 3 for the right deck.

In case you need to use different Inputs for your Timecode units, open the Sixty-Two Audio Driver panel and change the USB-3 and USB-4 Record for Deck 1 and Deck 2 to the appropriate PH/CD inputs.

Timecodes to Inputs 1 and 3

Timecodes to Inputs 2 and 4

Alternatively, you may observe and control the status of the Timecode Inputs by assigning toggle '@$Rane62TCA' and toggle '@$Rane62TCB’ to 2 custom skin buttons. Your settings will be remembered across sessions.
Connect your Timecode devices at the rear panel of the Rane 62 to the Inputs 1 and 3 (or different if defined as above)

Click on the ON buttons from the Timecode panels of the Default Skin to enable the Timecode control to the left and/or right deck.

Press PLAY on your Timecode CD or Vinyl device and VirtualDJ will automatically detect your Timecode type and make the appropriate adjustments for best performance.

Open the Timecode tab of the VirtualDJ Settings and choose the CALIBRATE button if for any reason the signal is not detected (possibly due to reversed phase connections).

Timecode Detection

Timecode On/Off buttons - 2 Decks default skin

Tip ! If no Timecode Inputs need to be used, it is suggested to delete the Timecode lines from the pre-defined audio configuration and save your custom audio settings as an alternative profile.

Sampler Output

VirtualDJ routes the Sampler Output to the USB AUX channel (Outputs 5 and 6) providing the ability to control its Volume, apply Filter and Effects from the USB AUX section of the Rane 62. See Auxiliary/Sampler

You may specifically route the Sampler output to deck 1, deck 2, both decks and active deck. In that case, you will need to delete the Sampler line from the Audio configuration and choose the desired Output via the Sampler Options.

Back to back

The Rane Sixty-Two has two USB ports, allowing simultaneous connection of two computers. Each port is completely independent. It is possible to run VirtualDJ on one computer and any other 3rd-party DJ-software on the other, Mac or PC.

How to:
  • Connect the 2nd computer to the unused USB port on the Sixty-Two.
  • Switch the DECK SOURCE on the non-playing Mixer channel to the USB source of the 2nd computer.
  • Play a track on this deck and mix it when ready – you ll now have audio from both computers during the mix.
  • Fade out the audio playing from the 1st computer to the audio playing from the 2nd one.
  • When only audio from the 2nd computer is left in the mix, remove the first computer.
  • Assign the DECK SOURCE for the remaining free Mixer channel to the 2nd computer and keep mixing.


The Rane Sixty-Two has a dedicated Input to record your Main Mix (default setting) or the Microphone. VirtualDJ has pre-configured this input for recording, thus no special setting is required in order to record your mix (including analogue sources and Microphone).

Simply make sure the Main Mix is selected as in the Rane sixty-Two Audio Driver control panel for the USB 6 Record Input and use the REC or BSCAST buttons from the Master center panel of the VirtualDJ GUI.

Record Selection – Rane Control Panel

Record section – Master GUI panel

For further Technical features and specifications, visit

Rane Sixty-Two
Product's Page

Hardware Integration Department

Reproduction of this manual in full or in part without written permission from Atomix Productions is prohibited.