Hardware Manuals


Hercules - Inpulse 300 MK2  

Pads




KEY

ACTION

SHIFT ACTION

M1 HOTCUE
Mode 5 : Sets Pads to Keycue page (led will be flashing)
M2 Loop
Sets Pads to Loop page (led will be turned on solid)
Mode 6 : Sets Pads to FX page (led will be flashing)
M3 Slicer
M4 SAMPLER


Pad modes can be assigned to a different Pads page. See https://www.virtualdj.com/manuals/virtualdj/interface/decks/decksadvanced/pads.html#controller


FX MODE


Press and hold (for about 1 second) the ROLL mode button [M2] to set the Pads to FX mode (led will be flashing). The Inpulse300 FX* Pads page will be also displayed on the GUI of VirtualDJ, reflecting the operation of the 8 Pads. The functionality of the Pads in this mode is mostly hard-coded in the Inpulse firmware and most of it cannot be changed. As a result of this hardware functionality, the Pads on the GUI do not offer any functionality if triggered from GUI, they just offer an aid showing the selected FX mode and an idea of what each Hardware pad does.

*Note: This special Pads Page will be available to select, only if the Inpulse 300 MK2 is connected.

Inpulse300MK2 FX Pads Page


KEY

ACTION

SHIFT (SECONDARY) ACTION

PAD 1
Press and hold Pad 1 to trigger the Filter LP Effect. The pad also controls the 1st Parameter of the LP Filter effect, starting from the zero value and gradually increasing to the maximum, as long as the pad is pressed. Effect is turned on when the pad is released (momentary)
No function is assigned
PAD 2
Press and hold Pad 2 to trigger the Filter HP Effect. The pad also controls the 1st Parameter of the HP Filter effect, starting from the zero value and gradually increasing to the maximum, as long as the pad is pressed. Effect is turned on when the pad is released (momentary)
No function is assigned
PAD 3
Press Pad 3 to trigger the Reverb * Effect. The pad also assign the 1st Parameter of the Reverb effect to a certain value, and gradually fast-decreases deck's Volume to the minimum. Effect is turned on when the pad is pressed again (toggle)
No function is assigned
PAD 4
Press Pad 4 to trigger the Echo * Effect. The pad also assign the 1st Parameter of the Echo effect to a certain value, and gradually fast-decreases deck's Volume to the minimum. Effect is turned on when the pad is pressed again (toggle)
No function is assigned
PAD 5
Press and hold Pad 5 to trigger the Beat Grid Effect. The Effect is turned off when the pad is released (momentary)
No function is assigned
PAD 6
Press and hold Pad 6 to trigger the Flippin Double Effect. The Effect is turned off when the pad is released (momentary)
No function is assigned
PAD 7
Press and hold Pad 7 to perform a "Baby" Scratch effect at the current position. The Scratch is turned off when the pad is released (momentary)
No function is assigned
PAD 8
Press and hold Pad 8 to jump at the 1st assigned Hotcue and perform a "Baby" Scratch effect from that position. The Scratch is turned off when the pad is released (momentary)
No function is assigned


Notes
* For best results on the Reverb and Echo Effects, it is advised to enable the Post Fader Effects setting (from VirtualDJ Settings->Options tab->fxProcessing setting to Post-fader). This will allow these Effects to continue trailing for a while, when the Volume fader is moved to the minimum position

** If you wish to replace the assigned Pads page of the FX Mode (Mode 6), you will need to disable the Hardware functionality. To do so, open VirtualDJ Settings->OPTIONS tab->CONTROLLER sub-category and select the Software mode for the FXmode setting


FX Mode Setting




For further Technical features and specifications, visit

Hercules DJ CONTROL INPULSE 300 MK2
Product's Page






Hardware Integration Department
2023 - ATOMIX PRODUCTIONS



Reproduction of this manual in full or in part without written permission from Atomix Productions is prohibited.