Quick Sign In:  

Forum: Old versions

Topic: VDJ PRO FULL TIMECODES

Dieses Thema ist veraltet und kann veraltete oder falsche Informationen enthalten.

Hi, I am new to the Virtual DJ community, and I have the Pro Full software.

My setup is as follows:

Pair of Pioneer CDJ 1000 MKII's
Hercules MK4 mixer
Maya 44 USB ESI

My problem is that my timecodes are cutting out after 10 or 12 minutes. The only answers I could find to this problem is that a person does not have the PRO FULL software. I, however, do have this.

Can anyone please help?
 
geposted Tue 04 Oct 11 @ 3:21 pm
after 12 Minutes ? thats about the length of the Timecode "Song" !

perhaps youve missed that..

than you have to start playing again from the Track beginning!
 
geposted Wed 05 Oct 11 @ 2:20 am
 
geposted Wed 05 Oct 11 @ 5:07 am
you could try to put the track on a loop and use the relative timecode setting, it would have to be a pretty big loop though...
 
geposted Wed 05 Oct 11 @ 7:08 am
I make sure to not let the 12 minutes run out. In other words, while one CDJ is playing, I restart the track on the other CDJ, so that the 12 minutes doesn't actually run out. But I'm still losing complete functionality from the CDJ's. By this point, I'm only able to use my MK4 to control the software.
 
geposted Wed 05 Oct 11 @ 10:01 am
I have tried using the Timecodes in Smart Relative, Relative, and Absolute. Each time is the same result. The functionality of my CDJ's stops working and I can only control the software through my Hercules MK4. Again, I do not let the 12 minutes expire on my CDJ's.

 
geposted Wed 05 Oct 11 @ 9:43 pm
I have switched my mixer to a Pioneer DJM 350, so I have a full Pioneer set up now with analog inputs as opposed to USB connection. However, nothing has changed with the Timecodes. I STILL CAN NOT GET MY CDJ's TO WORK FOR MORE THAN 10 TO 15 MINUTES AT A TIME, WITHOUT RE-APPLYING MY CONFIGURATION.

IF ANYONE WOULD LIKE TO HELP, THAT WOULD BE GREAT.
 
geposted Sun 09 Oct 11 @ 11:54 pm
 
geposted Tue 11 Oct 11 @ 12:50 am
bluntfusionn -

I followed your links, and did everything exactly as instructed for the advanced configuration with 2 timecodes. My timecode graphs are still in the shape of squares. And my functionality on my CDJ's still stops after the 10-15 time is up.
 
geposted Tue 11 Oct 11 @ 8:33 pm
Also, when I use my crossfader, hi's, mid's, low's, volumes, or anything else on my mixer, it responds perfectly. But I get no reading on the software showing that I'm moving anything.
 
geposted Tue 11 Oct 11 @ 8:35 pm
djblackout88 wrote :
My timecode graphs are still in the shape of squares. And my functionality on my CDJ's still stops after the 10-15 time is up.


This means that they are still not configured properly (The input signal is probably too loud.) Make sure that you are using the Pro-grade timecode signal from http://www.virtualdj.com/products/timecode/cd.html

djblackout88 wrote :
Also, when I use my crossfader, hi's, mid's, low's, volumes, or anything else on my mixer, it responds perfectly. But I get no reading on the software showing that I'm moving anything.


Please see http://www.virtualdj.com/wiki/Soft%20Take-over%20or%20Non-MIDI%20Mixer.html
 
geposted Wed 12 Oct 11 @ 5:27 am
pseftPRO InfinityMember since 2009
/
im using Consumer grade sound level for my 400's, is that correct timecodes
 
geposted Mon 17 Oct 11 @ 3:39 am
If they work OK, then that's fine.

If not, then you should try the pro grade signal.

NOTE: The only difference between the two is the pro-grade signal is recorded with lower gain to account for the more 'hot' output of higher-end CD players.
 
geposted Mon 17 Oct 11 @ 5:31 am


(Alte Themen und Foren werden automatisch geschlossen)